Bandry

Production

How to record percussion (congas, cajón, shakers and tambourine)

By the Bandry Team  ·  Nov 16, 2026  ·  6 min read

The conga part made the chorus move in rehearsal. On the recording it's a dull thud with a slap that pokes out of the mix, and the shaker on top sounds like it's limping, loud on one stroke and gone on the next. Learning how to record percussion is mostly about two things: where the mic sits, and how the player moves in front of it.

Hand percussion is tricky because it covers everything at once. A conga has deep low end and a sharp slap. A shaker or tambourine lives almost entirely in the brightest part of the sound, where a close mic turns harsh fast. And because the player's hands and body move, the sound changes from hit to hit in a way a kick drum never does.

Start With One Good Mic

You don't need a percussion locker of mics. A decent condenser, often the same one you use for vocals, covers most hand percussion well. A dynamic mic is a solid choice for loud, low hand drums like congas and djembe. Distance and angle change the sound far more than the mic does, so spend your time moving it, not shopping.

  • Closer means more attack. More slap, more finger detail, less room.
  • Further means more tone. More of the drum's ring and the space around it, and a softer top end.
  • Listen on headphones. Have the player loop the part while you move the mic a few inches at a time.

How to Record Congas and Hand Drums

Congas sound good under almost any mic, which makes them a great place to learn. For one drum, start with a mic roughly a foot above the head, angled toward where the player strikes. For two or three congas, use a pair of matching mics, each the same distance from its drum, so no drum jumps out louder than the others.

  • Mind the strike point. Where the player hits the head changes the tone a lot. Agree on it before you blame the mic.
  • Try underneath for boom. A mic under the open bottom of the drum adds deep low end and softens the slaps. Blend it in, don't rely on it alone.
  • Check the pair in mono. Two mics on two drums should still sound full when summed, the same check you'd run on a drum kit's overheads.

How to Record a Cajón

A cajón does two jobs: the slap on the front panel plays like a snare, and the boom out of the sound hole plays like a kick. Start with one mic in front of the panel the player hits, about a foot away. If the low end is missing, add a second mic a few inches from the sound hole on the back and blend the two.

Every cajón's sound hole behaves differently, so try a few positions and angles before the take. And watch the chair: a creaky seat ends up on every quiet bar.

How to Record Shakers and Tambourine

Shakers and tambourines are the hardest small parts to get right, because they're bright and the player's motion shapes the rhythm.

  • Shake across the mic, not at it. Shaking straight at the mic makes the forward stroke much louder than the backstroke, so the groove limps. Turning sideways evens the two out.
  • Back off. Up close, a shaker turns fizzy. A few feet of distance softens the top end and adds some air.
  • Put the mic above the tambourine. A mic a few feet up, looking down at the player, tames the harshest jingle. Too close and it cuts through everything.
  • Pick the right one. A softer shaker or a tambourine with fewer jingles often sits in a mix better than the loudest one in the bag.

Timing matters more on these small parts than on almost anything else in the song, because a shaker plays every subdivision and any drift is obvious. Give the player a headphone mix with plenty of hi-hat and snare, or the click, and not much else. Have them play the whole song rather than punching in bar by bar, so the feel stays the same from start to finish. Three or four steady full takes beat one heroic take stitched from pieces.

Layer the Parts and Make Them Sit

At home, percussion is usually overdubbed after the drums and bass. Loop the song or a section, let the player take several passes, and keep the best. Layering a few passes of a shaker or tambourine, panned a little apart, makes a part feel wider and steadier than one take ever does.

Close-miked percussion can sound dry and lifeless on its own. A little room mic or a shared reverb puts it in the same space as the band. Then keep it down: percussion is seasoning, and a good part is one you miss when it drops out, not one you notice on every hit. Bring it up until it moves the song, then pull it back a touch. If a part fights the hi-hat, try moving it to the other side of the stereo field or simplifying the rhythm instead of turning it down further.

Using Bandry for this

Need a percussionist for the session, or a room with space for a full setup? Drop a Seeking post on the Bandry Bulletin for Percussion, a Session musician or a Studio, and when someone who fits taps 🔗, their contact lands in your Linkups inbox. The Resources tab also runs a live Apple Maps search for studios near you. Start with recording studios near you.

Frequently asked questions

How do you mic congas?

Congas are forgiving, so most mics work. For one drum, start with a mic about a foot above the head, angled toward where the player strikes. For two or three drums, use a pair of matching mics, each the same distance from its drum, so the drums sound even. Move closer for more slap and attack, further back for more of the drum's ring.

How do you record a cajón?

Start with one mic in front of the panel the player hits, about a foot away, which catches the slap and snare sound. If you want more low end, add a second mic a few inches from the sound hole in the back, then blend the two. Every cajón's sound hole behaves a little differently, so try a few positions before the take.

Why does my shaker recording sound uneven?

Shaking straight at the mic makes the forward stroke much louder than the backstroke, so the rhythm limps. Turn sideways and shake across the mic instead, which evens the two strokes out. Step back a little too: shakers are bright, and a mic right in front of one turns fizzy. A steady, relaxed motion matters more than the mic.

What mic is best for recording percussion?

A good condenser handles most hand percussion, from shakers to congas, and it is often the same mic you use on vocals. A dynamic mic is a fine choice for loud, low hand drums. Distance and angle change the sound more than the mic does, so experiment with placement before you think about buying anything new.

Should percussion be recorded with the band or overdubbed?

Most home recordings overdub it. Once the drums and bass are down, the percussion player can lock to them, take a few passes, and try different instruments for different sections. A percussionist playing live with the band in one room sounds great too, but the bleed into other mics means you cannot fix a single shaker hit later.

Ready to try it?

Bandry is live on the App Store. Download it and start posting.

Download

Follow Bandry